Description
Please see specifications below:
Please click here if the requirement is only for horizontal use with upward radiation.
This is a URP- V Panel that can be used in the upside-down and vertical positions. Compared to the standard horizontal URP Panel this URP-V Panel additionally uses comb-type special materials and URP Fractal-Pins (pictures shown) and collars so that the panels may be used upside down and under vertical conditions.
For additional technical information or purchase, please contact MHI 513-772-0404 or [email protected] or please order directly through this store.
For the replacement element (only) for an existing panel please click here.
Mechanical Dimensions Per Panel. Please refer to the diagram above for dimensions. For layout possibilities, please see diagram alongside.
L1 = 12″
L2 = 12″
L3 = 9.5″
L4 = 10″
T= 1.125″ (thickness of thermal shock resistant insulation slab below the heater coil).
Specifications:
Nominal Power/Panel: The MHI URP Heating Panel is a universal scalable radiant panel that offer high temperatures of 1200C-1400C at ~1.8 kilowatts (this is the maximum temperature range and maximum power allowed for the heating coils (looped)).
• Each panel features special heating GAXP flat- coils (as shown) and Fractalin-ceramic spacers (not all shown) that are mounted firmly on a thermal shock resistant insulation slab.
• This is a scalable module.
• Please only construct a furnace enclosure with these panels with approval by a local electrician – the panels carry current and can heat to high temperature.
• Each panel has two terminals below the ceramic board (not shown in the picture).
• For nonvertical and non-upside down panels please choose the low-cost horizontal URP Panel.
When using please ensure that no specification is exceed i.e. of the rated current, voltage, power and temperature, together. This heating panel can be used with a BPAN control system which can also be acquired from MHI Inc. Please email [email protected] or call 513-772-0404.
Electrical Specifications: Each Panel ~ Maximum panel volts are 58 Volt, maximum current should not exceed 30 Amps (RMS maximum). The maximum coil temperature should not exceed 1350C on the coil as measured with a two-color optical pyrometer. Note that two units in series equal 110V-120V plug-in.
Control Options:
• One URP panel – BPAN-O-PLUS and Power Transformer (choose a BPAN-O-PLUs-120 or BPAN-O-PLUS-220) and Power Transformer.
• Two URP panels in series- a BPAN-O-PLUS-120 (no transformer required).
• Four URP Panels in series- a BPAN-O-PLUS-220 (no transformer required)
• Controls for more than 4 URP Panels – please contact MHI. ([email protected] or 513-772-0404
A control and an over-temperature thermocouple should be chosen for the BPAN-O-PLUS Control Panel. Thermocouple options are shown. Please also choose the thermocouple extender wire for each thermocouple.
Four panels may be connected in series for a 220-240V plug-in configuration. Balanced series-parallel connections may be used (purple and red in the picture). All measurements are reported in the free radiating mode.
For layout possibilities, please see diagram alongside.
L1 = 12″
L2 = 12″
L3 = 9.5″
L4 = 10″
T= 1.125″ (thickness of thermal shock resistant insulation slab below the heater coil).
Lu = 7″ (Terminal Length). The terminals protrude about 6″ from the insulation board bottom (on the other side of the heating face). Users may request shorter Lu for quantity purchases.
Options:
The connectors comprise clip-type connectors (that are used to connect the wire and solid terminal) and two wires. One set, when chosen from the options menu comprises two clips and two wires i.e one for each lead. Ratings of the connectors are 35 amp wire carrying capacity. Dimension – 6″ wire.
If required to extend beyond the 6″ standard, please contact MHI and we will be happy to accommodate the request as best as we can.
When checking out, the weight will be calculated with the control panel option.
The correct weight and shipping price will be shown in the final acknowledgment from MHI.